Every repair visit includes a full diagnostic and a written quote before work starts. If we find a second issue while we are in there, we tell you and price it separately. No surprise charges.
We test the thermostat, capacitor, contactor, blower motor, fan motor, and defrost board with a digital multimeter, clamp meter, and capacitor tester. We also check refrigerant pressures with a manifold gauge set. Diagnosis takes 30 to 45 minutes.
If the system is low, we use a leak detector to check flare fittings, Schrader valves, and coil joints. Finding the leak first saves you from paying for a recharge that leaks right back out. We repair the leak, then evacuate and recharge.
We clean the indoor and outdoor coils with a coil cleaning pump and fin comb, and we flush the condensate drain line. Dirty coils and clogged drains cause most frozen coil and water leak calls we see in Manassas.
After the repair, we verify voltage and amp draw at the indoor and outdoor units. We run the system in heat and cool mode for 15 to 20 minutes and check the temperature split. You see the numbers before we leave.
Most repairs carry a one-year warranty on parts and labor. If the same part fails inside that window, we come back at no charge. We also give you a filter schedule so you can protect the repair.
Heat Pump Mini-Split Repair Manassas VA is the diagnostic and mechanical work that restores a ductless heat pump to full heating and cooling capacity. A mini-split has two main halves: an outdoor condenser and one or more indoor air handlers connected by refrigerant lines. When something fails, the whole zone goes down. We test the capacitor, contactor, reversing valve, blower motor, and defrost board, then check refrigerant charge with a manifold gauge set and vacuum pump. Most repairs take two to four hours and cost $180 to $450 in parts and labor.
Manassas homeowners call us most in October and November, when the first cold snap hits and a mini-split that cooled fine all summer suddenly blows cold air in heat mode. Others call in July when a frozen coil stops cooling a bedroom over the garage. If you search for Heat Pump Mini-Split Repair Manassas VA near me, you want a tech who carries the right parts. We stock capacitors, fan motors, thermostats, and R-410A so we can finish the job the same day.
Five steps from your first call to a working system. No mystery, no waiting around all day.
Schedule
Call or book online — a real human picks up and confirms a 2-hour arrival window.
Diagnose
Licensed tech inspects on-site, then walks you through the cause and your options.
Fix
The job is completed to code and done right the first time — no shortcuts, no surprises.
Guarantee
Every job backed by a written workmanship warranty — and we stand behind it.
Manifold gauge set
Reads high-side and low-side refrigerant pressures so we can confirm charge and diagnose reversing valve and compressor issues on ductless systems.
Vacuum pump and refrigerant recovery machine
Recovers old refrigerant, pulls a deep vacuum after a leak repair, and lets us recharge with R-410A or R-32 to manufacturer spec without contaminating the system.
Leak detector
Finds refrigerant leaks at flare fittings, Schrader valves, and coil joints. Finding the leak first is what separates a real repair from a recharge that leaks back out.
Digital multimeter and clamp meter
Tests voltage, continuity, and amp draw at the indoor and outdoor units. We use these to confirm capacitor, contactor, blower motor, and fan motor failures.
Capacitor tester
Measures microfarad rating on run and start capacitors. A capacitor that reads low or swollen is a confirmed failure, not a guess.
Coil cleaning pump and fin comb
Cleans indoor and outdoor coils and straightens bent fins. Dirty coils cause frozen coils, high head pressure, and higher electric bills.
EPA Section 608 refrigerant handling
Every tech who touches refrigerant holds EPA Section 608 certification. We recover, evacuate, and recharge by the book, which protects your system and the environment. It also keeps the work compliant with federal rules.
NATE-aligned diagnostics
We follow NATE certification standards for testing heat pump not heating and heat pump not cooling complaints. That means a defined sequence: thermostat, electrical, airflow, then refrigerant. It prevents replacing parts that are still good.
ACCA quality standards
We size, test, and commission systems to ACCA quality standards. On repairs, that means verifying airflow and temperature split after the fix, not just confirming the part turns on. You see the numbers before we leave.
OSHA safety compliance
We follow OSHA safety compliance on every call, from lockout procedures on electrical panels to safe refrigerant handling. It protects our techs and your home. You will see us use PPE and test before we touch a circuit.
01
What we do: We come out same day, check refrigerant pressures, and test the capacitor and blower motor. If the coil is dirty or the charge is low, we clean the coil, find and repair any leak, and recharge with R-410A or R-32 to spec.
→ Cold air back in the room the same afternoon. Most customers see the temperature drop within 30 minutes of us finishing.
02
What we do: We test the reversing valve and defrost board, which are the two most common failures in heat mode. We carry both parts on the truck, so we can replace the failed one during the same visit and verify the defrost cycle.
→ Heat restored the same day. You avoid a cold night and the compressor stress that comes from running a system that cannot heat.
03
What we do: We flush the condensate drain line, clear the trap, and check the float switch. If the drain pan is cracked or the line is pitched wrong, we repair that too. We also clean the coil while we are there.
→ No more water on the floor or wall. The system drains properly and you avoid drywall and flooring damage that can cost hundreds to fix.
04
What we do: We diagnose fan motor bearings, loose panels, compressor noise, and refrigerant line vibration. Most noise calls trace back to a worn fan motor or blower motor, which we replace on the spot if we have the part.
→ Quieter operation and a motor that will not fail in the middle of winter. Catching it early usually saves the cost of a compressor later.
Manassas sits in a climate that swings hard. Summers push 95 degrees with high humidity, and winters drop into the teens. That range is tough on ductless heat pumps. In October and November, we get a wave of calls for heat pump not heating and blowing cold air in heat mode, usually a defrost board or reversing valve. In July and August, the calls shift to frozen coil and heat pump not cooling, often from a dirty coil or low refrigerant. Older homes in the Manassas Historic District and Georgetown South often have attic-run lines and tight clearances, which makes leak detection slower. Newer builds in Yorkshire and The Retreat at Battlefield usually have cleaner access. We work under Virginia HVAC license and Manassas County contractor license, and we follow EPA Section 608 rules on every refrigerant job. If you need affordable ductless mini-split repair in Manassas Virginia, we know the housing stock and the parts that fail here.
Old Town Manassas
Older homes with retrofitted ductless systems. Line sets often run through tight chases, so leak detection takes longer. We plan extra time for these calls.
Bull Run
A mix of single-family homes with multi-zone mini-splits. We see a lot of branch box and zoning valve issues here, especially on systems more than eight years old.
Loch Lomond
Many homes here have outdoor units under decks or in shaded side yards. That shade keeps coils damp, so we clean coils and check for corrosion more often.
Yorkshire
Newer construction with cleaner line-set runs. Repairs go faster here, and we often finish a capacitor or fan motor swap in under two hours.
Humid summers that push condensate drains hard
Clogged condensate drain lines are one of our most common summer calls in Manassas. We flush the line and check the float switch on every cooling repair to prevent water damage.
Cold snaps that expose defrost board failures
When temperatures drop into the 20s, a weak defrost board lets the outdoor coil ice up. We test the board and replace it so the system can heat properly through winter.
Older housing stock with tight line-set chases
In the Manassas Historic District and Georgetown South, line sets run through walls and attics with little slack. Leak detection and line repair take longer, and we price that honestly.
Pollen and debris that clog outdoor coils each spring
Spring pollen coats outdoor coils and restricts airflow. We clean coils with a coil cleaning pump and fin comb, which lowers head pressure and improves efficiency.
These are the calls we run most in Manassas County. If your system is doing any of these, call us before it gets worse.
Problem
A reversing valve or defrost board failure leaves you with no heat in January. Running the system in this state can also stress the compressor and lead to a much bigger repair bill.
Our Fix
We test the reversing valve with pressure readings and check the defrost board with a multimeter. Once we confirm which one failed, we replace it and run the system in heat mode for 20 minutes to verify the fix. Most of these jobs finish same day.
Problem
Ice blocks airflow and the system stops cooling. If you keep running it, the compressor can fail from liquid refrigerant returning to it. That turns a $300 repair into a $2,000 replacement.
Our Fix
We thaw the coil, then find the cause: low refrigerant, a dirty coil, or a failing blower motor. We repair the leak or replace the motor, clean the coil with a coil cleaning pump, and verify the temperature split before we leave.
Problem
A clogged condensate drain line sends water down your wall or across the floor. Left alone, it damages drywall, trim, and flooring, and can trigger mold growth behind the wall.
Our Fix
We flush the condensate drain line, clear the trap, and test the float switch. If the drain pan is cracked or the line is pitched wrong, we fix that too. This is usually a quick, inexpensive repair that prevents expensive water damage.
Problem
Short cycling wears out the compressor and contactor, raises your electric bill, and leaves rooms uncomfortable. It usually gets worse over a few weeks until the system stops altogether.
Our Fix
We check refrigerant charge with a manifold gauge set, test the capacitor and thermostat, and inspect the defrost board. Once we find the cause, we repair it. If the system is oversized, we tell you that too and give you honest options.
We fix ductless systems, not just patch them. Here is what you get when you call us for mini-split repair in Manassas.
Same-Day Service
We run same-day Heat Pump Mini-Split Repair Manassas VA appointments six days a week. Call before noon and we aim to be at your door by late afternoon. Our trucks carry the common parts: capacitors, contactors, fan motors, thermostats, and R-410A refrigerant. That means one visit, one repair, and your heat back on.
Upfront Repair Pricing
You get a price before we start. Diagnostic is $89 and we credit it toward the repair. A capacitor swap runs $180 to $260. A refrigerant leak repair with recharge runs $350 to $850 depending on line length and access. No surprise line items, no pressure to replace a system that still has life left.
Licensed and Insured Techs
Every technician holds EPA Section 608 certification and works under our Virginia HVAC license and Manassas County contractor license. We follow ACCA quality standards and OSHA safety compliance on every call. That matters when someone is handling refrigerant or opening an electrical panel in your home.
All Major Brands
We repair Mitsubishi Electric, Daikin, Carrier, Trane, Lennox, Goodman, Rheem, York, Bosch, and American Standard mini-splits. Whether your wall unit is a single-zone or a four-zone system, we have the gauges, adapters, and service manuals to diagnose it correctly the first time.
Typical 2026 pricing in this area runs $180 to $450 for most repairs, with a $89 diagnostic that we credit toward the work. A capacitor or thermostat replacement sits at the low end. A refrigerant leak repair with recharge runs $350 to $850 depending on line length and access. Compressor or reversing valve jobs cost more. We quote before we start, so you know the number. If you want affordable mini-split repair Manassas VA homeowners trust, call us and we will give you a straight answer.
Typical Investment Range
$180 - $850 depending on scope
A $300 repair on a system with years of life left beats a $6,000 replacement. We tell you when repair makes sense and when it does not. No pressure either way.
What changes the price
Part cost
A capacitor runs $15 to $40, a blower motor $150 to $400, and a defrost board $120 to $300. Compressors and reversing valves cost more. Parts are the biggest swing in the final price.
Refrigerant type and charge
R-410A and R-32 cost different amounts per pound, and a system can take anywhere from two to eight pounds. A leak repair plus recharge adds $200 to $500 to the job.
Access to the unit
A mini-split with a clear outdoor unit and accessible line set takes less time. Units under decks, in tight chases, or on roofs add labor. We tell you upfront if access changes the price.
Leak location
A leaking flare fitting is a quick fix. A leak inside a wall or in the coil takes longer to find and repair. Line-set replacement, when needed, adds $300 to $700.
Number of zones
A single-zone system is simpler than a four-zone system with a branch box. Multi-zone diagnostics take longer because we test each zone and the branch box valves.
Google ★★★★★4.9
Fast, honest, and they had the part on the truck. Our mini-split capacitor failed on a Friday and they fixed it the same day. The tech showed me the old part and the meter reading. Fair price and no upsell.
Yelp ★★★★★4.8
They found a refrigerant leak that another company missed. Used a leak detector and showed me the bubbles at the flare fitting. Repaired it, pulled a vacuum, and recharged. Cold air has held for months now.
BBB ★★★★★4.9
Called about water leaking from our wall unit. They flushed the drain line and cleaned the coil while they were there. Took about 90 minutes and the price matched the quote. We use them for maintenance now.
Google ★★★★★5.0
Our ductless unit was blowing cold air in heat mode. They diagnosed a bad defrost board and replaced it the same afternoon. Explained the defrost cycle and what to watch for. Heat has worked all winter.
Our techs work on ductless heat pumps every week, not once a season. We hold EPA Section 608 certification for refrigerant handling and follow NATE certification standards for diagnostic work. Every job is done under our Virginia HVAC license and Manassas County contractor license. We carry manifold gauge sets, vacuum pumps, refrigerant recovery machines, leak detectors, and clamp meters on every truck. We also stock the parts that fail most: capacitors, contactors, blower motors, fan motors, reversing valves, defrost boards, and thermostats. That local experience means fewer second trips and faster repairs for you.
Real experiences from customers who chose our Heat Pump Mini-Split Repair services.
“Our Mitsubishi mini-split stopped cooling the upstairs bedroom in July. The tech found a leaking flare fitting, repaired it, pulled a vacuum, and recharged with R-410A. He showed me the gauge readings before and after. Cold air in about three hours. Price was $520, which matched the quote.”
Dana R.
Homeowner, Old Town Manassas
“First cold snap in October and our ductless unit was blowing cold air in heat mode. They diagnosed a bad defrost board and had the part on the truck. Fixed it the same afternoon. I appreciated that they tested the reversing valve too instead of just guessing. No issues since.”
Marcus T.
Homeowner, Bull Run
“Called about a mini-split that was short cycling and making a grinding noise. Turned out to be the outdoor fan motor. They replaced it, checked the capacitor, and cleaned the coil while they were there. The system runs quieter and my electric bill dropped about $40 the next month.”
Priya S.
Homeowner, Loch Lomond
Real answers to the questions we hear most often from local homeowners and property managers.
Whole-system heat pump repair for central units and mini-splits. We diagnose not heating, not cooling, short cycling, and loud noise complaints across Manassas. Same-day appointments and upfront pricing.
View Heat Pump RepairNew ductless mini-split and central heat pump installation in Manassas. We size the system, run lines, and commission it. Proper install prevents the leaks and short cycling we get called to fix later.
View Heat Pump InstallationAnnual maintenance keeps your mini-split efficient. We clean coils, check refrigerant charge, test capacitors, and flush condensate drain lines. Two visits a year prevents most emergency calls in Manassas.
View Heat Pump MaintenanceNo heat at 2 a.m. or no cooling during a July heat wave. We run emergency heat pump repair in Manassas for failed compressors, blown capacitors, and refrigerant leaks. Call and we will get a tech out.
View Emergency Heat Pump RepairA tune-up covers coil cleaning, filter replacement, refrigerant check, and electrical testing. It is the cheapest way to avoid a mid-winter breakdown. We recommend one every fall in Manassas.
View Heat Pump Tune-UpLow refrigerant is the top cause of a mini-split that runs but does not cool. We use leak detectors and manifold gauge sets to find the leak, repair it, and recharge with R-410A or R-32.
View Heat Pump Refrigerant Leak RepairCall us at (571) 760-4910 or email [email protected]. We answer the phone 24/7 for emergencies. For routine service, we schedule same-day or next-day appointments. Our office is in Manassas, and we serve all of Manassas County and nearby towns.
Phone
(571) 760-4910Address
9101 Mike Garcia Dr, Manassas, VA 20110
Hours
Mon–Fri: 7AM – 7PM
Sat: 8AM – 4PM
Sun: Emergency Only
24/7 Emergency Available
